4/14/2024 0 Comments Micro molex connector![]() Will the same tool work for all?ĭon't know what other Molex is in my future in my -12 build. So, what crimping tool is appropriate for these Micro-Fit pins?ĭon't know what other Molex is in my future in my -12 build. Here are some tools I've been able to locate but not sure if they handle the right size: I saw a reference to a specific tool hnere but that was a general Molex discussion and can't tell whether it covers the Micro-Fit pins. These connectors include a lead-in feature in the connector housing for blind mating of receptacle to plug. The problem is, the pins provided in the kit don't identify the size. Molex has developed seven series of Micro-USB Type B and Type AB receptacles in a selection of top-, bottom- and mid-mount versions, and a new series of USB A to Micro-USB B cable assemblies. Micro-Fit 3.0 Connector System Product Family Micro-Fit 3.0 Connector Systems, available in multiple circuit sizes and cable lengths for power and signal applications, offer a 3.00mm pitch, a 10. They all seem to accommodate at least three sizes just judging from the picture. I've been through most of the Molex threads and don't seem much smarter than I was before. I'm trying to find the right tool to crimp the Micro-Fit pins for the pitch trim servo (page 11-07). USB 2.0 and Micro-B offer an IP67-rated waterproof option that withstands. Many consumer and industrial applications experience wet conditions that could cause failure in connectors. If I know I can get a small cutter back on the connecters after installation I will sometimes use tie-wrap to secure them together if there is insufficient room for back-shells but, without a back-shell, there may not be enough strain relief on the wires in case the bundle gets pulled. With 3.0A/5.0A current to enable faster and safer charging, Molex offers a wide range of USB Type-C Connectors that are physically robust and electrically reliable. Too much solder and the pin won't insert.įor low-amp stuff (< 3A 14V) I now use D-SUB connector. There are only two locations to crimp: the outer one that captures the wire jacket and the next one in that makes contact with the stripped wire.įinally, I like to hit the inner crimp with a tiny bit of solder - but only after I'm happy with the crimp, not in lieu of a good crimp. Micro-Fit 3. OEMs often need power connectors in space-constrained applications. If you crimp those it both deforms the pin making it hard to insert and prevents it from latching into the molex housing because you've destroyed the latching flanges. The Micro-Fit Connector Family offers up to 8.5A with a 3.00mm pitch, delivering power in a compact package in wire-to-wire and wire-to-board configurations. I've found my most common mistake is to accidentally crimp the latching flanges that splay out from the pin or barrel housing at about a 30 degree angle. Applications often require rugged terminals and lower mating force to reduce operator fatigue during assembly and/or to withstand high-mating cycles.Those pins are fussy. The pre-lubricated version can be mated up to 250 times and fit into standard Micro-Fit 3.0 Housings. Micro-Fit 3.0 RMF (Reduced Mating Force) Terminals are designed for applications needing lower engagement and disengagement forces or when the units are cycled frequently. For lower applied costs, OEMs often prefer a compliant pin connector over one that requires soldering. The Micro-Fit 3.0 CPI Header mates with Micro-Fit 3.0 Receptacle, allowing running changes as boards transition from solder to press-fit applications. The robust eye-of-the-needle design provides a reliable interface when recommended board layouts are followed. Micro-Fit 3.0 CPI (Compliant Pin) Connectors provide a compliant pin interface while maintaining all the features of the standard Micro-Fit 3.0 Connector. The TPA reduces terminal back-out by providing locking redundancy assemblers cannot insert the TPA unless terminal is properly inserted. ![]() The Micro-Fit TPA Connector Family helps prevent failure in end products by offering terminal position assurance (TPA). Doing so can cause damage to the connector and/or terminal and consume valuable labor time. In hard-to-reach applications, such as drawers or fan assembly trays, connectors need to be mated and unmated without being seen. They allow mating misalignment (per product drawing). ![]() Micro-Fit 3.0 Blind-Mate Interface (BMI) Connectors are designed for blind-mating applications. The Micro-Fit Connector Family offers up to 8.5A with a 3.00mm pitch, delivering power in a compact package in wire-to-wire and wire-to-board configurations.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |